VVDI PROG Programmer

Top 8 Reasons to Get VVDI Prog:

1. Support R&W lots of chips, include MC9S08 series, MC68HC(9)12 series,MC9S12 series, V850 series, H8X series, R8C series, PCF79XX series and most eeprom chips
2. Support chip data verify, check blank function
3. Support data file compare function
4. Support R&W BMW N20, N55 ECU ( show ISN directly )
5. Stable R&W MC9S12XE series chips (5M48H/1N35H/2M53J/3M25J etc.)
6. Support renew PCF79XX remote, currently support BMW E/F series
7. Lots of connection diagram
8. Support Multi-language now: English, Arabic, Czech, French, Italian, Polish, Portuguese, Russian, Spanish, Turkish & Chinese Simplified
 

This function require internet support
Click the “Upgrade” button enter the upgrade interface, show as following picture

Enter update interface, if software show ”communication with server failed”,please close your Anti-virus and computer firewall and retry. If software show “unable to find equipment”, please reconnect device

Tip information show the latest software version and upgrade information
 Device information show the device SN, device firmware version and the latest firmware version

 Firmware upgrade steps:
1. Select the firmware version
2. Click “Start Firmware Upgrade” button
3. Don’t close or pull out USB cable before upgrade finished

Software upgrade steps:
1. Click “Software Link 1” or “Software Link 2” button, download software from the web
2. Extract the file

VVDI Prog Programmer Supported Type List:

Memory:
ATMEL,CATALYST,EXEL,FAIRCHILD,INTEL,MICROCHIP,MITSUBISHI,ST,TOSHIBA,XICOR

MCU:
RENESAS V850,RENESAS H8X,RENESAS R8C,MOTOROLA MC68HC(9)08,MOTOROLA MC68HC(9)12
MOTOROLA MC9S08,MOTOROLA MC9S12,NXP PCF79XX,ST ST10F,INFINEON XC2XXX,ATMEL,ATMEGA XXXX,
INFINEON XC164CS,MICROCHIP PIC18F,

VVDI Prog Programmer Support Model List:

ECU List:
BMW E Series,BMW F Series,BOMBARDIER,CHANGAN,DELPHI,MAGNETI,MARELLI,RENAULT,OTHER

IMMOBILIZER List：
AUDI,BENZ,BMW,BUCIK,CHEVROLET,STEC,CHRYSLER,FIAT,FORD,GREATWALL,INFINITI,LANDROVER,
JAGUAR,NISSAN,OPEL,PORSCHE,RENAULT,SAICMOTOR,VOLKSWAGEN,ZHONGHUA.

DASHBOARD List:
BUICK,CHANGAN,CHERY,CHEVROLET,DONGFENG,FAW,FORD,GEELY,GREATWALL,HAFEI,TOYOTA,
HANTENG,HAIMA,HONDA,JAC,JAGUAR,JINBEI,JMC,LUXGEN,NISSAN,SGMW,VOLOVO,ZHONGHUA,ZOTYE

REMOTE List:
BMW E Series,BMW F Series

VVDI PROG Connection for Maybach:

VVDI Prog Programmer Unit Description:

1.16 Pin DIP socket Function: 
Read EEPROM chips Use method: Follow the image direction when insert the DIP chip (PIN1 as yellow point show as the picture); 
SOP chip need soldering on 16Pin adaptor first, then insert the chip follow the image direction 

2. MCU Reflash Cable 
    Function:       Read & Write MC68HC(9)12, V850, H8X, R5C series chips,current version is V2 
   Use method: Soldering the line on pin of chip before read & write 
    Notes: 
     (1) Please check all connection lines,ensure correct and reliable connection 
     (2) Please Don’t lengthen CLK and GND-C line, maybe cause read data failed. 

3. ECU Reflash Cable 
        Function:          Read & Write engine ECU 
        Use method:   Connect the ECU and R&W 
        Notes:               Please check all connection lines, ensure correct and reliable connection 

4.MC9S12 Reflash Cable 
     Function:  Read & Write MC9S08, MC9S12 series chips, current version is V1 
     Use method: Soldering the line on pin of chip before read & write 
     Notes: 
       (1) Please check all connection lines,ensure correct and reliable connection. 
       (2) Please Don’t lengthen CLK and GND-C line, maybe cause read data failed. 

VVDI Prog Programmer Feedback:

did a few tests today and this is what I found out.
It seems that VVDI prog reading speed is dependent on the processor speed of the computer.
CAS3 0L15Y flash read times
Centrino processor @ 1.6ghz Windows XP = 12mins
Core2 Duo processort @ 2.5ghz Windows 7 32 bit = 5 mins
i7 @ 4.4ghz Windows 7 64 bit = 2mins 30 seconds.
Other programmers do not seem to be affected by processor speed at all.
I also would of thought this was a fairly easy question to answer without me doing all the testing
Tested by me: cas 2, cas 3, cas 3+, Cas4 5m48h, volvo cem v40 all ok.
Is a very good tool and for bmw cas4 .
I tested today D80 and a m35080v6, and they work perfect.
Mine erased D160 (BMW F01 dash) with no problem.
Tried to renew bmw e series 868 key. Vvdi programmer claimed operation success but in tango key is now recognized as transponder type A. locked
I did renew 2 keys! Both worked and now are programmed to cars!
Only thing you need to disconnect from PCB is battery while writing the renew file. (Remove the batteries)
Renew BMW series E 868 key – 100% OK z vvdi-prog v4.5.7
FRM3 works perfectly
More EDC17 under ECU section would be great!
Especially BMW EDC16 and EDC17 for ISN purposes.
BMW F series FEM module reading but for that i can only dream about…
BMW BMSX bike ECU would be great…
Renew pcf7946 and 29f family
Renew E series remote with pcf7942 / pcf7944 would be fine
Unlock and download the 9S12G128 secure without erasing it first would be nice .
erasing all 35080s and d80 with soic clip would be super nice too!
I read the CAS3+ MCU with VVDI Prog and that worked perfect.
BMW FRM3 series Exx – READ and WRITE – OK
BMW KEY series Exx – OK
BMW DashBoard 6WB 160DQWT – READ , ERASE , WRITE – OK

VVDI Prog Reviews: 
2004 Suzuki Jimny: 
 The first job i did with this kit was actually a 2004 Suzuki Jimny, literally within around 30 – 45 minutes of the parcel being delivered. The software was quick and easy to install (No cd provided, need to download from dealer website and update to latest version). 

Anyway, for the Suzuki i used the VVDI-prog with the EEPROM clip adapter to read the immobox 24c01 in-circuit. Then using the VVDI2 immobiliser data tool, i was able to create a dealer key with an Xhorse 4d/4c chip. Write the new dump back to the immobox with VVDI-prog, put it all back together and worked first time thankfully after previous failed attempts with other devices. 
 Anyway end goal complete and happy with the new purchase 

BMW EWS3: 
 I did some testing on the bench with a BMW EWS3 using VVDI2 with the CAS adapter cable (Needs external 12Vdc supply). It reads the EWS ok, but can’t write a file back to EWS. 
 I will try reading the EWS3+ that is in my car and produce a dealer key for it. 

The file change km’ seems to read from dump ok, and will allow you to modify file with new km (untested on car though). If i get some time later on will try read/write with VVDIprog. 

VVDI Prog Programmer Package List: